Correcting Uneven Paver Surfaces

Uneven pavers can really mess up your yard’s look and become a tripping hazard. It’s frustrating when your nice patio or walkway starts to sink or tilt. Luckily, there are ways to fix this, from simple adjustments to more involved systems. We’ll walk through how to figure out what’s going on and what you can do about it, including looking at some smart paver leveling correction systems that can make a big difference.

Key Takeaways

Start by figuring out why your pavers are uneven – it could be the base, drainage, or just the pavers themselves. This helps you choose the right fix.
There are systems designed specifically for leveling pavers, often involving adjusting the base material or using special supports.
Before fixing, clear the area, remove any bad pavers, and check that the ground underneath is ready for repair.
Techniques include adding or compacting base material and carefully putting the pavers back in place to get a flat surface.
For long-term stability, think about drainage and how to keep your paver surface maintained over time.

Assessing Paver Surface Irregularities

Uneven paver surfaces can be more than just an eyesore; they can become tripping hazards and lead to further damage if not addressed. Before you can fix them, you need to figure out why they’re uneven in the first place. It’s like a doctor diagnosing an illness before prescribing medicine.

Identifying Causes of Uneven Pavers

Several things can cause your pavers to shift and settle. Sometimes it’s simple, like a loose paver here or there. Other times, it’s a sign of bigger problems happening underneath.

Poor Base Preparation: This is a big one. If the ground wasn’t properly compacted or graded before the pavers were laid, it’s going to settle over time. Think of it like building a house on sand – it’s not going to last.
Inadequate Drainage: Water is a paver’s worst enemy. If water can’t drain away properly from under the pavers, it can freeze and expand in winter, or just wash away the base material over time, causing settling.
Soil Movement: Depending on your soil type, it can expand and contract with changes in moisture and temperature. Clay soils, for example, are notorious for this.
Heavy Loads: Regularly driving or parking heavy vehicles on a paver surface not designed for that kind of weight can cause significant settling and cracking.
Erosion: Wind and water can erode the sand between the paver joints, eventually weakening the base and leading to movement.

Evaluating the Extent of Surface Distortion

Once you know the potential causes, you need to see how bad the problem really is. Walk the area and look for specific signs.

Visible Low Spots or High Spots: Are there areas where the pavers dip noticeably or stick up higher than the surrounding ones?
Loose or Wobbly Pavers: Try rocking individual pavers with your foot. If they move easily, they’re likely not seated properly.
Cracked or Broken Pavers: This often happens when pavers are forced out of alignment or are under stress from an unstable base.
Edge Deterioration: Are the pavers along the edges of your patio or walkway shifting or crumbling?

The key is to look beyond the surface. What you see on top is often just a symptom of an issue deeper down. Ignoring these early signs can lead to more extensive and costly repairs later on.

Recognizing Signs of Sub-Base Issues

The sub-base is the foundation for your pavers. If it’s failing, your pavers will too. Here are some indicators that the problem lies beneath the surface:

Widespread Settling: If large sections of your paver area are sinking, it points to a problem with the entire base layer, not just a few loose pavers.
Water Pooling: If water consistently sits on the surface after rain, your drainage is likely compromised, which will eventually affect the sub-base.
Cracks Extending Beyond Pavers: Sometimes, cracks in the underlying soil or aggregate base can manifest as cracks or significant shifts in the paver surface.
Visible Erosion Around Edges: If you see sand or base material washing away from the perimeter, it means water is carrying away the support structure. This is a clear sign of foundation settlement repair needs, even if it’s for a hardscape rather than a building.

Taking the time to thoroughly assess these irregularities will help you choose the right correction method and prevent future problems.

Understanding Paver Leveling Correction Systems

Components of Paver Leveling Systems

When your pavers start to look a bit wonky, it’s not just an eyesore; it can become a tripping hazard. Luckily, there are systems designed to fix this. These systems aren’t usually one single product but a combination of materials and techniques. Think of them as a toolkit for bringing your paver surface back to life. The main players usually involve some kind of base material, often a mix of sand and aggregate, and sometimes specialized leveling compounds or grids. The goal is to create a stable, even foundation underneath the pavers themselves. Proper base preparation is the bedrock of any successful paver installation or repair. Without it, you’re just putting a band-aid on a bigger problem.

How Paver Leveling Correction Systems Work

These systems work by addressing the root cause of uneven pavers, which is almost always related to the base beneath them. Over time, the ground can shift, water can wash away supporting material, or the initial compaction might not have been sufficient. Leveling systems essentially provide a way to re-establish that stable base. This might involve:

Adding or adjusting base material: This could mean digging down a bit to add more compacted gravel or sand to low spots.
Using a leveling agent: Some systems use a fine aggregate or a special leveling sand that can be spread thinly to fill small voids and create a smooth surface.
Re-compacting the area: Once the base material is adjusted, it needs to be firmly compacted to prevent future settling.
Re-laying pavers: After the base is corrected, the pavers are put back in place, often with a bit of tapping to settle them into their new, level position.

It’s a process of carefully rebuilding the foundation so the pavers can sit evenly and securely. This approach is key to preventing future issues and ensuring the longevity of your hardscape. For more on building a stable foundation, understanding proper soil compaction is really important.

Benefits of Using Paver Leveling Correction Systems

Why bother with these systems? Well, the benefits are pretty clear. First off, safety. Uneven pavers are a major trip hazard, especially for kids and older adults. Fixing them makes your outdoor space much safer to walk on. Then there’s the look of it. A level paver surface just looks good. It makes your patio, walkway, or driveway appear well-maintained and attractive. Beyond that, these systems help prevent further damage. When water pools on an uneven surface, it can seep under the pavers, freeze and expand in colder climates, or just generally degrade the base material faster. By leveling the surface, you improve drainage and protect the integrity of the entire installation. It’s about making your pavers look better, last longer, and be safer to use.

Preparing the Paver Area for Correction

Before you can start fixing those uneven pavers, you really need to get the area ready. It’s not just about grabbing a tool and digging in; a little prep work goes a long way. Think of it like getting your kitchen ready before you start cooking a big meal – you need everything clean and in its place.

Clearing and Cleaning the Paver Surface

First things first, you’ve got to clear everything off the pavers. This means moving any furniture, planters, grills, or whatever else you usually have sitting on your patio or walkway. Once it’s clear, give the whole area a good sweep. Get rid of all the loose dirt, leaves, and debris. If there’s any moss or stubborn weeds growing between the pavers, now’s the time to tackle those too. A stiff brush or a pressure washer can work wonders here. A clean surface lets you see exactly what you’re dealing with. You don’t want to be trying to level things only to find out there’s a hidden rock or a big clump of dirt causing a problem.

Removing Loose or Damaged Pavers

Now, take a closer look at the pavers themselves. You’ll probably need to pull up some of them to get to the base material underneath. If any pavers are cracked, chipped, or just look really bad, it’s best to remove them now. You can set them aside and replace them later with new ones, or if they’re still in decent shape, you might be able to reuse them. Gently pry them up using a paver puller or a flathead screwdriver and pliers. Try not to damage the pavers next to them. It’s also a good idea to label or mark the pavers so you know where they go back, especially if you have a specific pattern.

Assessing and Preparing the Sub-Base

This is probably the most important step. Once the pavers are up, you need to check out the layer underneath – the sub-base. This is usually a mix of gravel and sand. Look for any areas that have sunk or washed out. Is the base material compacted well, or is it loose and crumbly? You might need to add more base material, especially in the low spots. If the ground beneath the base is soft or muddy, that could be a bigger issue related to drainage. You want a firm, stable base that drains well. Sometimes, you might need to dig down a bit deeper to add more gravel or a stabilizing layer. A well-prepared sub-base is key to a long-lasting, level paver surface.

The condition of the sub-base directly impacts the stability of the pavers above. Neglecting this layer often leads to recurring settling and unevenness, no matter how well the pavers themselves are reset.

Implementing Paver Leveling Correction Techniques

So, your pavers aren’t looking so hot anymore? Maybe they’ve started to dip in places, or perhaps a few are sticking up a bit too much. It happens. The good news is, you can often fix this without tearing everything out. This section is all about getting those pavers back in line.

Adjusting the Base Material

This is where the real work begins. Most paver issues stem from what’s underneath – the base material. Over time, this base can shift, wash out, or just settle unevenly. The goal here is to get that base solid and level again.

First, you’ll need to remove the loose or damaged pavers from the affected area. This gives you access to the base. Don’t just yank them out; try to keep them in good condition if you plan to reuse them.
Next, assess the sub-base. Is it compacted? Is there evidence of water erosion? You might need to add more gravel or crushed stone to build up low spots. For areas that have sunk significantly, you might need to excavate a bit deeper to ensure a solid foundation.
Compact the new or existing base material thoroughly. This is super important. A plate compactor is your best friend here. You want that base to be firm and stable, ready to support the pavers without shifting.

Proper compaction of the base material is the single most critical step in preventing future settling and ensuring a long-lasting paver surface. Skipping this can lead to repeating the same repairs sooner than you’d like.

Utilizing Compaction and Stabilization Methods

Once you’ve adjusted the base material, you need to make sure it stays put. This is where compaction and stabilization come in.

Re-compacting the entire area after adding material is key. You’re not just compacting the new stuff; you’re re-settling everything to create a uniform, dense layer.
Consider stabilization. For areas that get a lot of traffic or are prone to moisture issues, adding a stabilizer to the base material can make a big difference. This could be a specific binder or even a geotextile fabric laid beneath the base to prevent mixing with the soil below and improve load distribution. This helps with drainage too.
Use a vibrating plate compactor for best results. Make sure to go over the area multiple times, in different directions, to achieve maximum density. This step is vital for creating a stable foundation for your pavers.

Re-laying Pavers for a Level Surface

With a solid, level base, it’s time to put the pavers back. This is the part where you start to see the results of your hard work.

Start laying pavers from a straight edge or a corner, working your way across the corrected area. This helps maintain alignment.
Use a rubber mallet to gently tap each paver into place. This ensures they are fully seated on the base material and level with their neighbors. You can use a level across several pavers to check for consistency.
Fill the joints. Once all the pavers are laid, sweep jointing sand into the gaps between them. This locks the pavers together and prevents them from shifting. You might need to do this a couple of times, compacting lightly between applications, to get the sand settled in properly. For a more permanent solution, consider polymeric sand, which hardens and creates a more stable joint. This whole process is about restoring the integrity of your paver surface.

Advanced Paver Leveling Correction Systems

Sometimes, the usual fixes just don’t cut it. When you’re dealing with paver surfaces that have settled unevenly or have persistent issues, you might need to look at more advanced systems. These aren’t your everyday patch-up jobs; they’re designed for more complex situations or for creating a perfectly level surface from the start, especially in areas where precise height is important.

Adjustable Pedestal Systems for Pavers

Adjustable pedestal systems are pretty neat. They use a series of adjustable supports, often made of durable plastic or metal, to hold up pavers. This is super common for rooftop decks or elevated patios where you need a level surface over an uneven or sloped base. You can tweak each pedestal to get the exact height you need, creating a perfectly flat plane for your pavers. It’s a bit like building on stilts, but way more stable and designed for this purpose. This method also helps with drainage because water can flow freely underneath the pavers.

Key Components:
- Adjustable pedestals (fixed or screw-type)
- Paver support trays or direct paver placement
- Edge restraints
- Optional drainage mats

Gravel and Sand Base Adjustments

When you’re not dealing with an elevated system, adjustments to the base material are still a big deal. For ground-level paver installations, the base is usually a mix of compacted gravel and sand. If settling occurs, it often means this base layer has shifted or wasn’t compacted properly in the first place. Advanced techniques involve carefully excavating around the affected area, adding more compacted gravel, and then a fresh layer of leveling sand. Sometimes, a geotextile fabric is laid down first to help separate the layers and improve stability over time. This is all about rebuilding that solid foundation that the pavers sit on.

Proper base preparation is absolutely critical for any paver installation. Skipping steps or not compacting adequately here is a recipe for future problems, no matter how nicely you lay the pavers themselves.

Geotextile and Drainage Layer Integration

Integrating geotextile fabrics and specialized drainage layers is a more sophisticated approach to paver base construction and repair. Geotextiles act as a separator, preventing the finer sand layer from mixing with the coarser gravel base, which maintains the integrity of each layer and improves load distribution. For drainage, systems might include perforated pipes or a more substantial gravel drainage layer, especially in areas with high water tables or heavy rainfall. This proactive approach helps manage water effectively, preventing the freeze-thaw cycles and saturation that often lead to paver settlement and instability. It’s about building a system that works with nature, not against it. For areas needing robust waterproofing, looking into waterproofing systems for low-slope surfaces might offer insights into managing water effectively, even if applied differently.

Benefits of Integrated Layers:
- Improved load-bearing capacity
- Enhanced long-term stability
- Better water management and reduced erosion
- Prevention of soil migration between base layers

Addressing Sub-Surface Drainage Issues

Sometimes, the problems with your pavers aren’t just on the surface. Water is a sneaky thing, and if it’s not draining away properly from under your pavers, it can cause all sorts of headaches. Think about it: water gets in, freezes, expands, and then thaws. This cycle is a major reason why pavers can start to shift and sink over time. It’s not just about the pavers themselves; it’s about what’s happening underneath.

Identifying Drainage Problems Affecting Pavers

How do you know if drainage is the culprit? Look for a few key signs. Are there areas where water consistently pools after it rains, even hours later? Do you see more settling or sinking in certain spots compared to others? Sometimes, you might even notice weed growth or moss appearing in areas where the base material is staying too wet. These are all indicators that water isn’t moving away like it should. It’s like a leaky faucet in your house – a small problem that can lead to bigger issues if ignored. Addressing these drainage problems is key to a lasting paver surface.

Implementing Drainage Solutions for Paver Areas

So, what can you do about it? There are a few ways to tackle poor drainage. For minor issues, sometimes just regrading the area slightly can make a big difference. You want a gentle slope away from structures and towards a suitable drainage point. For more persistent problems, installing a French drain system can be a really effective solution. This involves digging a trench, filling it with gravel, and often including a perforated pipe to carry water away. It’s a bit more work, but it directly addresses the water buildup beneath the pavers. Another option is to ensure your paver base is properly compacted and includes a layer of aggregate that allows for good water flow. This helps water drain through the base material instead of sitting there and causing trouble.

Regrading: Create a slight slope away from buildings and towards a lower point.
French Drains: Install perforated pipes in gravel-filled trenches to channel water away.
Base Material: Use well-draining aggregate for the paver base and compact it properly.
Geotextiles: Consider a geotextile fabric layer to prevent soil migration into the drainage layers.

Ensuring Proper Water Runoff Management

Ultimately, the goal is to manage water so it doesn’t undermine your paver installation. This means thinking about the entire system, from the roof gutters and downspouts that direct water to the ground, to the grading of your yard, and the drainage layers beneath your pavers. If water from your roof is dumping right next to your patio, that’s a problem that needs fixing at the source. Making sure water flows away from, not towards, your paver areas is a big part of preventing future settling and damage. It’s all about creating a pathway for water to leave the area without causing harm. For more complex site drainage, understanding how to manage stormwater can provide valuable insights.

Proper drainage isn’t just about preventing puddles on the surface; it’s about protecting the integrity of the entire paver system from the ground up. Ignoring it is a recipe for future repair headaches.

Restoring Paver Integrity and Appearance

After you’ve dealt with the unevenness, it’s time to make things look good again. This means fixing any broken bits and making sure the whole surface is solid and looks uniform. It’s not just about making it flat; it’s about bringing back that finished look you want.

Replacing Damaged or Missing Pavers

Sometimes, during the leveling process, or just from wear and tear, you’ll find pavers that are cracked, chipped, or completely gone. You can’t just leave these spots empty or covered up. Replacing them is pretty straightforward, but you need to get it right.

Remove the Damaged Paver: Carefully pry out the broken paver. If it’s really stuck, you might need to use a chisel or even a small saw to cut it into pieces for easier removal. Be careful not to damage the surrounding pavers.
Prepare the Space: Clean out the hole. You want to remove any old sand, dirt, or debris. Make sure the base underneath is firm and level.
Insert the New Paver: Place the new paver into the spot. It should sit flush with the surrounding pavers. You might need to tap it gently with a rubber mallet to set it.
Fill the Joints: Once all replacements are done, sweep new jointing sand over the surface to fill the gaps between the pavers. This locks them in place.

Getting the right color and type of paver for replacements is key to a seamless look. If you can’t find an exact match, try to find one that’s very similar in size, thickness, and color tone. Sometimes, older pavers weather differently, so a new one might look a bit brighter at first.

Re-sanding and Sealing Paver Joints

After all the adjustments and replacements, the joints between your pavers might be low on sand or just look worn. Adding new jointing sand is a critical step. It helps lock the pavers together, preventing them from shifting and stopping weeds from growing in the gaps. You’ll want to sweep a good quality paver sand into all the joints until they’re completely full.

Once the joints are filled and the surface is clean, consider sealing the pavers. A good quality paver sealer does a few things:

Protects the Surface: It shields against stains from oil, grease, and other spills.
Enhances Color: It can bring out the natural color of the pavers, making them look richer and more vibrant.
Prevents Weed Growth: While not foolproof, it makes it harder for weeds to take root in the joints.
Stabilizes Joints: It helps keep the jointing sand in place, especially during heavy rain.

Applying sealer is usually a spray-on job, and you’ll want to follow the manufacturer’s instructions carefully. Make sure the pavers are completely dry before you start.

Achieving a Uniform and Stable Surface

The final goal is a paver surface that not only looks good but feels solid underfoot. This means ensuring all pavers are at the same height and that the entire area is stable. After re-sanding and sealing, give the area a final check. Walk across it, feel for any loose spots, and look for any remaining low areas. A well-maintained paver surface can last for many years, providing a beautiful and functional outdoor space. Proper drainage is also a big part of keeping your pavers stable long-term; if water sits on the surface or under the base, it can cause problems down the road. Consider solutions for managing water runoff if you notice pooling.

The process of restoring paver integrity involves meticulous attention to detail, from replacing individual units to ensuring the long-term stability and aesthetic appeal of the entire installation. It’s about bringing the surface back to its intended condition, making it both visually pleasing and structurally sound for continued use.

Long-Term Maintenance for Paver Surfaces

Keeping your paver surfaces looking good and functioning well for years to come really comes down to a few key things. It’s not just about the initial installation; a little ongoing attention goes a long way. Think of it like taking care of a car – regular check-ups and minor fixes prevent major breakdowns.

Regular Inspections of Paver Installations

Making it a habit to walk over your pavers a couple of times a year, maybe in the spring and fall, can really help. You’re looking for anything that seems out of place. Are any pavers wobbly? Have any shifted slightly? Is there any new cracking or significant weed growth in the joints? Catching these small issues early is way easier and cheaper to fix than waiting until a whole section starts to sink or break apart. It’s also a good time to check the edges to make sure they’re still secure and holding the pavers in place.

Preventative Measures Against Settling

Settling is probably the most common issue paver surfaces face over time. It usually happens because the base material underneath has shifted or compacted unevenly. To help prevent this, make sure your initial installation had proper drainage. If you notice areas that seem to hold water after rain, that’s a red flag for potential future settling. Sometimes, adding a bit more jointing sand can help stabilize things, especially if the old sand has washed out. For more serious settling, you might need to lift pavers, add more base material, and re-compact. This is where understanding how paver leveling correction systems work can be really useful.

Routine Cleaning and Joint Maintenance

Keeping your pavers clean is more than just aesthetics. Regular sweeping or a gentle power wash (on a low setting!) can remove dirt, debris, and organic matter that can break down the jointing sand or encourage weed growth. Weeds are a nuisance, but they can also lift pavers and compromise the joint stability. If you see weeds popping up, pull them out promptly and consider topping up the jointing sand. Using a good quality polymeric sand can make a big difference here, as it hardens and helps lock the pavers together while resisting weed growth and erosion. This type of maintenance is similar to keeping up with your pool deck coatings to ensure their longevity.

The key to long-term paver performance isn’t a single grand gesture, but a series of small, consistent actions. Regular visual checks, prompt weed removal, and ensuring proper drainage are simple steps that significantly extend the life and appearance of your paver installations. Don’t underestimate the power of routine care.

Professional Assistance for Paver Leveling

Sometimes, paver issues go beyond a simple DIY fix. When you’re facing significant settling, widespread unevenness, or suspect deeper problems with the base layers, it might be time to call in the pros. Trying to tackle complex paver leveling on your own can sometimes lead to more problems, especially if you don’t have the right tools or a solid understanding of what’s causing the unevenness in the first place. Knowing when to seek professional help is key to a lasting solution.

When to Call a Professional Paver Installer

There are a few clear signs that indicate it’s time to bring in an expert. If your pavers have settled unevenly over a large area, or if you notice significant dips and valleys that make walking or driving difficult, it’s a strong signal. Also, if you’ve tried minor fixes and the problem keeps coming back, a professional can diagnose the root cause. Issues like poor drainage that consistently lead to paver problems, or damage that seems to stem from the sub-base, are often best handled by experienced installers. They have the equipment and knowledge to address these more involved situations.

Extensive settling across a large section of the paver area.
Persistent unevenness despite previous attempts at correction.
Visible signs of sub-base failure or erosion.
Recurring drainage problems affecting paver stability.
Damage that appears to be structural rather than superficial.

Evaluating Contractor Expertise in Paver Leveling

When you decide to hire a professional, it’s important to find someone with specific experience in paver leveling and repair. Don’t just look for a general landscaping company; seek out those who specialize in hardscaping and paver installations. Ask about their experience with similar projects, what methods they typically use for leveling, and how they address underlying issues like drainage and sub-base preparation. A good contractor will be able to explain the process clearly and provide references. It’s also wise to get multiple quotes to compare pricing and proposed solutions. Remember, proper yard grading is often a part of a good paver installation, so look for that understanding too.

Understanding Project Timelines and Costs

The time and cost involved in professional paver leveling can vary quite a bit. Factors like the size of the area, the severity of the unevenness, and the complexity of the required repairs all play a role. Simple adjustments might take a day or two, while a full restoration involving sub-base work and re-laying could take several days or even weeks. Costs will reflect the labor, materials (like new base material, sand, or even replacement pavers), and any specialized equipment needed. Always get a detailed estimate that breaks down these costs and provides a realistic timeline. Be wary of quotes that seem too low, as they might indicate corners being cut, which could lead to future problems.

Professional paver leveling isn’t just about making the surface look good; it’s about restoring its structural integrity and preventing future damage. This often involves more than just adding sand; it requires a thorough assessment of the entire system, from the sub-base to the drainage.

Wrapping Up Your Paver Project

So, you’ve tackled those uneven pavers, and hopefully, your walkway or patio is looking much better now. It’s not always the most glamorous job, but getting those pavers level makes a big difference in how your outdoor space looks and feels. Plus, it’s safer to walk on! Remember, a little bit of effort now can save you from bigger headaches down the road. Keep an eye on your pavers, and don’t be afraid to do a quick check-up every now and then. Enjoy your newly improved outdoor area!

Frequently Asked Questions

Why did my pavers become uneven?

Pavers can get uneven for a few reasons. Sometimes, the ground underneath them shifts over time, especially if it wasn’t packed down well at first. Heavy things being driven or parked on them can also cause them to sink. Water can also play a role, washing away the sand between the pavers or softening the base beneath them.

What’s the easiest way to fix uneven pavers?

For small uneven spots, you might be able to lift the paver, add a little sand or gravel underneath, and then press it back down firmly. For larger areas, you might need to remove more pavers, fix the base material, and then put them all back. Sometimes, special leveling systems can help too.

Do I need to remove all the pavers to fix them?

Not always! If only a few pavers are out of place, you can often fix them individually. However, if a large section is uneven or sinking, it’s usually better to remove that whole section. This lets you properly fix the base material underneath before putting the pavers back.

What is a ‘sub-base’ and why is it important for pavers?

The sub-base is the layer of material, like gravel or crushed stone, that goes directly under your pavers and the sand they sit on. It’s super important because it provides a solid foundation, helps with drainage, and stops the pavers from sinking or shifting. If the sub-base isn’t right, your pavers won’t last long.

How can I stop water from causing problems with my pavers?

Good drainage is key! Make sure the ground slopes away from your paver area so water doesn’t pool. Sometimes, adding a layer of gravel or using special drainage systems can help move water away faster. Keeping the joints between pavers filled with sand also helps prevent water from washing out the base.

What are adjustable pedestal systems for pavers?

These are special supports, often made of plastic, that you can adjust to make them taller or shorter. They’re usually used for paver patios or decks that are raised off the ground. They help create a perfectly level surface even if the base underneath isn’t completely flat.

How often should I check my paver patio for problems?

It’s a good idea to take a look at your pavers at least once a year, maybe in the spring. Check for any loose or wobbly pavers, cracks, or areas where the sand might have washed out. Catching small problems early can save you a lot of work later on.

When should I just hire a professional to fix my pavers?

If the unevenness is widespread, if you suspect major issues with the base or drainage, or if you’re just not comfortable doing the work yourself, it’s best to call a pro. They have the tools and experience to fix it right the first time, especially for larger projects.

TOEDWY

See Full Bio